You are not registered yet. Please click here to register!
Asus Rampage III Extreme - results thread - Page 7 - i4memory.com - different look at memory

Notices

Reply
 
Thread Tools
Old 14-06-2010, 03:01 AM   #49
eva2000
Administrator
eva2000's PC Specs
 
Join Date: Jul 22 2004
Location: Brisbane, Australia
Posts: 23,046
twitter.com/i4memorycom Facebook Page livestream.com/i4memorycom
Blog Entries: 42
wow you cpu is totally different from all the ones i've tested all mine need much higher cpu vtt (maybe board related will find out later )
eva2000 is offline   Reply With Quote
Old 14-06-2010, 08:36 AM   #50
Jammer
Senior Member
Jammer's PC Specs
 
Join Date: Mar 22 2006
Location: Melbourne
Posts: 2,009
By donmarkoni View Post
I edited some settings worth trying:
Code:
Target CPU Frequency		3800-4200MHz
Target DRAM Frequency		1603MHz

LN2 Mode:			Disabled***
QPI Loadline Calibration:	Enabled***

Sync Mode			[Disabled]
AI Overclock Tuner		[Manual]
OC From CPU level Up		[Auto]
CPU Ratio Setting		[19.0 / 21.00]
CPU Turbo Power Limit		[Disabled]

>CPU Configuration----------------------------
CPU Ratio Setting		[19.0 / 21.0]
C1E Support			[Disabled]
Hardware Prefetcher		[Enabled]
Adjacent Cache Line Prefetcher	[Enabled]
Intel(R) Virtualization Tech	[Enabled]
CPU TM Function			[Disabled]
Execute Disable Bit		[Enabled]
Intel(R) HT Technology		[Enabled]
Active Processor Cores		[All]
A20M				[Disabled]
Intel(R) SpeedStep(TM) Tech	[Disabled]
Intel(R) C-STATE Tech		[Disabled]
----------------------------------------------

BCLK Frequency			[200]
PCIE Frequency			[100]
DRAM Frequency			[1603]
UCLK Frequency			[3208]
QPI Link Data Rate		[7218MT/s]

Memory Configuration Protect	[Disabled]

>DRAM Timing Control--------------------------
CAS# Latency		      8	[8]
RAS# to CAS# Delay	      8	[8]
RAS# PRE Time		      8	[8]
RAS# ACT Time		     24	[24]
RAS# to RAS# Delay	      5	[Auto]
REF Cycle Time		     72	[Auto]
WRITE Recovery Time	     14	[Auto]
READ to PRE Time	      8	[Auto]
FOUR ACT WIN Time	     24	[Auto]
Back-To-BackCAS# Delay	      0	[Auto]

Timing Mode		     2N	[Auto]
Round Trip Latency on CHA    56	[Auto]
Round Trip Latency on CHB    57	[Auto]
Round Trip Latency on CHC    58	[Auto]

WRITE To READ Delay(DD)	      7	[Auto]
WRITE To READ Delay(DR)	      7	[Auto]
WRITE To READ Delay(SR)	     18	[Auto]
READ To WRITE Delay(DD)	      9	[Auto]
READ To WRITE Delay(DR)	      9	[Auto]
READ To WRITE Delay(SR)	      9	[Auto]
READ To READ Delay(DD)	      7	[Auto]
READ To READ Delay(DR)	      6	[Auto]
READ To READ Delay(SR)	      4	[Auto]
WRITE To WRITE Delay(DD)      7	[Auto]
WRITE To WRITE Delay(DR)      7	[Auto]
WRITE To WRITE Delay(SR)      4 [Auto]
----------------------------------------------

CPU Differential Amplitude	[Auto]
CPU Clock Skew			[Auto]
IOH Clock Skew			[Auto]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode			[T-Balanced]
PWR Volt. Control		[Auto]
Load-Line Calibration		[Full Calibration]
CPU Voltege OCP			[Enabled]
CPU PWM Frequency		[Auto]

Extreme OV			[Disabled]
Extreme OC			[Auto]

CPU Voltage		1.356	[1.30000-1.35000]
CPU PLL Voltage 	1.230	[Auto]
QPI/DRAM Core Voltage	1.230	[1.25000-1.30000]
DRAM Bus Voltage	1.654	[1.65625]

>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA	[Auto]
DRAM CTRL REF Voltage on CHA	[Auto]
DRAM DATA REF Voltage on CHB	[Auto]
DRAM CTRL REF Voltage on CHB	[Auto]
DRAM DATA REF Voltage on CHC	[Auto]
DRAM CTRL REF Voltage on CHC	[Auto]
----------------------------------------------

IOH Voltage		1.111	[Auto]
IOH PCIE Voltage	1.508	[1.51050]

ICH Voltage		1.111	[1.11300]
ICH PCIE Voltage		[1.51050]

---------- Spread Spectrum Control -----------
CPU Spread Spectrum		[Disabled]
DRAM Spread Spectrum		[Disabled]
CPU PLL Voltage 1.230 [1.23225] - 1.2??? was this a writing mistake?

BTW, congrats on writing actual settings before brackets, where they belong. I have seen people not doing this and confusing others with some old settings I used while making the template.
The CPU PLL volts are actually correct. Again I have found that I get no difference in stability from 1.2V CPU PLL or 1.8V CPU PLL. Will try it on auto see what it sets it to. However I'm afraid I just have a crap CPU and as for the other changes, I have tried all of them with no success. Except for the QPI LLC which I will try shortly. I beleive this is a jumper no?

By eva2000 View Post
wow you cpu is totally different from all the ones i've tested all mine need much higher cpu vtt (maybe board related will find out later )
Very weird indeed and hence why I think I'm doing something wrong. This has been the case with both my W3520, Core i7 930 and on both P6X58D Premium and Rampage III.
Jammer is offline   Reply With Quote
Old 14-06-2010, 08:50 AM   #51
donmarkoni
Senior Member
donmarkoni's PC Specs
 
Join Date: May 13 2009
Posts: 488
Yes.
And about CPU PLL, very strange, I can't even boot under 1.4V.
donmarkoni is offline   Reply With Quote
Old 18-06-2010, 03:28 AM   #52
donmarkoni
Senior Member
donmarkoni's PC Specs
 
Join Date: May 13 2009
Posts: 488
Sorry for double posting, but I needed to bump this thread, cause I need advice about CPU PLL.
Can it be dangerous to run CPU using so low PLL voltage? It is way under Intel's specs.

BTW. I'm testing new 4410/1680 settings. Now with AC on, cause the summer is killing me also, not just my rig.
Code:
Target CPU Frequency		4410MHz
Target DRAM Frequency		1683MHz

LN2 Mode:			Disabled***
QPI Loadline Calibration:	Enabled***

Sync Mode			[Enabled]
AI Overclock Tuner		[Manual]
OC From CPU level Up		[Auto]
CPU Ratio Setting		[21.0]
CPU Turbo Power Limit		[Disabled]

>CPU Configuration----------------------------
CPU Ratio Setting		[21.0]
C1E Support			[Enabled]
Hardware Prefetcher		[Enabled]
Adjacent Cache Line Prefetcher	[Enabled]
Intel(R) Virtualization Tech	[Enabled]
CPU TM Function			[Disabled]
Execute Disable Bit		[Enabled]
Intel(R) HT Technology		[Enabled]
Active Processor Cores		[All]
A20M				[Disabled]
Intel(R) SpeedStep(TM) Tech	[Enabled]
Intel(R) C-STATE Tech		[Enabled]
C State package limit setting	[Auto]
----------------------------------------------

BCLK Frequency			[210]
PCIE Frequency			[100]
DRAM Frequency			[1683]
UCLK Frequency			[3789]
QPI Link Data Rate		[7579]

Memory Configuration Protect	[Disabled]

>DRAM Timing Control--------------------------
CAS# Latency		      6	[6]
RAS# to CAS# Delay	      7	[7]
RAS# PRE Time		      6	[6]
RAS# ACT Time		     18	[18]
RAS# to RAS# Delay	      4	[4]
REF Cycle Time		     72	[72]
WRITE Recovery Time	     12	[10]
READ to PRE Time	      6	[6]
FOUR ACT WIN Time	     24	[Auto]
Back-To-BackCAS# Delay	      0	[Auto]

Timing Mode		     1N	[1N]
Round Trip Latency on CHA    59	[59]
Round Trip Latency on CHB    61	[61]
Round Trip Latency on CHC    62	[62]

WRITE To READ Delay(DD)	      8	[Auto]
WRITE To READ Delay(DR)	      8	[Auto]
WRITE To READ Delay(SR)	     18	[Auto]
READ To WRITE Delay(DD)	      7	[Auto]
READ To WRITE Delay(DR)	      7	[Auto]
READ To WRITE Delay(SR)	      7	[Auto]
READ To READ Delay(DD)	      7	[Auto]
READ To READ Delay(DR)	      6	[Auto]
READ To READ Delay(SR)	      4	[Auto]
WRITE To WRITE Delay(DD)      7	[Auto]
WRITE To WRITE Delay(DR)      7	[Auto]
WRITE To WRITE Delay(SR)      4	[Auto]
----------------------------------------------

CPU Differential Amplitude	[Auto]
CPU Clock Skew			[Auto]
IOH Clock Skew			[Auto]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode			[T-Balanced]
PWR Volt. Control		[Auto]
Load-Line Calibration		[Full]
CPU Voltege OCP			[Enabled]
CPU PWM Frequency		[1000kHz]

Extreme OV			[Disabled]
Extreme OC			[Auto]
Subzero Booster			[Auto]

CPU Voltage		1.402	[1.40000]
CPU PLL Voltage 	1.812	[Auto]
QPI/DRAM Core Voltage	1.330	[1.33750]
DRAM Bus Voltage	1.654	[Auto]

>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA	[Auto]
DRAM CTRL REF Voltage on CHA	[Auto]
DRAM DATA REF Voltage on CHB	[Auto]
DRAM CTRL REF Voltage on CHB	[Auto]
DRAM DATA REF Voltage on CHC	[Auto]
DRAM CTRL REF Voltage on CHC	[Auto]
----------------------------------------------

IOH Voltage		1.244	[Auto]
IOH PCIE Voltage	1.508	[Auto]

ICH Voltage		1.111	[Auto]
ICH PCIE Voltage		[Auto]

---------- Spread Spectrum Control -----------
CPU Spread Spectrum		[Disabled]
DRAM Spread Spectrum		[Disabled]



***on-board jumper dependant

Last edited by donmarkoni; 18-06-2010 at 03:46 AM.
donmarkoni is offline   Reply With Quote
Old 19-06-2010, 11:13 PM   #53
famich
Senior Member
famich's PC Specs
 
Join Date: Aug 01 2009
Posts: 113
OK, I am in

Donmarkoni,

I m in bought , mounted this awesome mobo and I must say, it s the best MB I have ever had .
Currently testing 4200 on my 3845A935 Xeon and I must say that 210 BCLK work with Patriot 6GB 1600 RAM at 8 8 8 24 1T, which was never possible on DFI X58.

Any hints , small tricks from your side will be greatly appreciated
Currently running 0402 BIOS / teh BIOS the board came with / Should I try any new beta ?
Cheers.
famich is offline   Reply With Quote
Old 20-06-2010, 03:26 AM   #54
donmarkoni
Senior Member
donmarkoni's PC Specs
 
Join Date: May 13 2009
Posts: 488
By famich View Post
Donmarkoni,

I m in bought , mounted this awesome mobo and I must say, it s the best MB I have ever had .
Currently testing 4200 on my 3845A935 Xeon and I must say that 210 BCLK work with Patriot 6GB 1600 RAM at 8 8 8 24 1T, which was never possible on DFI X58.

Any hints , small tricks from your side will be greatly appreciated
Currently running 0402 BIOS / teh BIOS the board came with / Should I try any new beta ?
Cheers.
Welcome to the club!
Yes, it is the best. It simply has everything, and looks great.
I'm running 4200 core/2000 memory as my summer settings, but testing 4410/1680. I also use 4305/1640 that is fully stable, but did not post settings. I'm also testing 4305/2050 but currently not very stable.
About tips and tricks... I don't know, it just works great, never had to look for workarounds.
You should try latest BIOS 0704 (in first post), it is best IMO.

@eva2000: What do you think about undervolting CPU PLL voltage (mentioned above)?
donmarkoni is offline   Reply With Quote
Old 20-06-2010, 05:23 AM   #55
eva2000
Administrator
eva2000's PC Specs
 
Join Date: Jul 22 2004
Location: Brisbane, Australia
Posts: 23,046
twitter.com/i4memorycom Facebook Page livestream.com/i4memorycom
Blog Entries: 42
nice famich, gem batch w3520 + r3e sounds like a good pairing

@donmarkoni, not sure CPU PLL for my boards I've tried min is 1.8v so haven't tried lower. Hear it's good for sub zero LN2 clocks, don't think it will hurt ??
eva2000 is offline   Reply With Quote
Old 20-06-2010, 07:02 AM   #56
famich
Senior Member
famich's PC Specs
 
Join Date: Aug 01 2009
Posts: 113
Thanks, guys, both of you As for the PLL, I have not tried lower one than 1.8 , same as eva2000
famich is offline   Reply With Quote
Reply

Bookmarks

Tags
asus, asus rampage iii extreme, asus rog, asus x58, extreme, iii, marvel sata3 raid, marvel sata6 raid, marvell 9128 raid, marvell 9128 sata3, rampage, rampage 3 extreme, results, thread


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools


Similar Threads for: Asus Rampage III Extreme - results thread
Thread Thread Starter Forum Replies Last Post
[Techpowerup.com] ASUS Shows Off ROG Rampage III Gene Motherboard News Reviews & News Online 0 29-05-2010 01:00 PM
[Techpowerup.com] ASUS Gives Rampage III Extreme 4-way SLI Capability with ROG Xpander News Reviews & News Online 0 20-05-2010 09:11 PM
i5 670 & ASUS P7P55D-DELUXE Motherboard 2D review Uncle Fester Asus Intel motherboards / CPU 9 18-03-2010 07:41 AM
[Legitreviews.com] Asus X58 Rampage III Extreme Motherboard Preview News Reviews & News Online 0 02-03-2010 03:41 AM
[Techpowerup.com] ASUS Rampage III Extreme Smiles for the Camera News Reviews & News Online 0 10-01-2010 03:01 AM


All times are GMT +11. The time now is 09:21 PM.