6GB Gskill Trident F3-16000CL9T-6GBTD Preliminary Test Results

03:10 AM

DFI LANPARTY UT X58-T3eH8
G.Skill F3-16000CL9T-6GBTD
Intel Core i7 920, D0 Stepping
Enermax Galaxy EVO 1250w
Heatsink:Prolimatech Megahalem-Push
Sapphire ATI Radeon HD4850 X2 2GB
Windows 7 Ultimate 64bit

Prime95 (Custom)
-Min. FFT size (in K) : 8k
-Max FFT size : 4096k
-Memory to use (in MB) : Max available in OS-100 MB.

Genie BIOS Setting

****CPU Feature****
Set VR Current Limit Max: Disabled
Thermal Management Control: Disabled
EIST Function: Enabled
CxE Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled

***** Logical Processor Setting *****
Intel HT Technology: Enabled
Active Processor Cores: All

******DRAM Timing******
Channel Interleave Setting: AUTO
Rank Interleave Setting: AUTO
Memory LowGap: 1024M
DRAM Command Rate: 2N
CAS Latency Time (tCL): 9
RAS# to CAS# Delay (tRCD): 9
RAS# Precharge (tRP): 9
Precharge Delay (tRAS): 24
REF to ACT Delay (tRFC): 88
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): 6
Row Cycle Time (tRC): 31
Read CAS# Precharge (tRTP): 6
Four ACT WIN Time (tFAW): 31
Ch1 Round trip latency: AUTO
Ch2 Round trip latency: AUTO
Ch3 Round trip latency: AUTO
tREFI: AUTO

*****Voltage Setting******
O.C. Shut Down Free: Enable O.C.S.D.F
CPU VID Control: 1.33750v
CPU VID Special Add Limit: Enabled
CPU VID Special Add: Auto
Vcore Droop Control: Enabled
DRAM Bus Voltage: 1.65v
DRAM PWM Switch Frequency: Nominal
DRAM PWM Phase Control: 2 Phase Operation
CPU VTT Special Add: Auto
CPU VTT Voltage: 1.48v
VTT PWM Switch Frequency: Nominal
VTT PWM Phase Control: 2 Phase Operation
CPU PLL Voltage: 1.80v
IOH/ICH 1.1V Voltage: 1.29v
IOH Analog Voltage: 1.25v
ICH 1.5 Voltage: 1.7v
ICH 1.05V Voltage: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF: -00.0%
DIMM 3/4 DQ/DQSTB Bus VREF: -00.0%
DIMM 5/6 DQ/DQSTB Bus VREF: -00.0%
ADDR/CMD VREF Control: Disabled
x DIMM 1/2 ADDR/CMD Bus VREF: 110
x DIMM 3/4 ADDR/CMD Bus VREF: 110
x DIMM 5/6 ADDR/CMD Bus VREF: 110
CPU QPI Drive Strength: Normal
IOH QPI Drive Strength: Normal

Exit Setup Shut down: Mode 2
O.C. Fail Retry Counter: Enabled
O.C. Fail CMOS Reload: Disabled
PPM Function: Enabled
Turbo Mode Function: Enabled
1 core Max Turbo Ratio: 22x
2 core Max Turbo Ratio: 21x
3 core Max Turbo Ratio: 21x
4 core Max Turbo Ratio: 21x
CPU Non-Turbo Clock Ratio: 20x

* BCLK/UCLK/QPI Controller Settings *
QPI Control Settings: Enabled
QPI Link Fast Mode: Enabled
QPI Frequency: 4.800GT/s (BLCK*18*2)
CPU Base Clock (BCLK): 189 Mhz
Boot Up CPU Base Clock: AUTO
PCIE Clock: 100 Mhz
DRAM Frequency: 10x Memory multipliers (1890Mhz)
UnCore Frequency: 20x Uncore multipliers (3780Mhz)
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

30-10-2009, 11:53 PM #18 (**permalink**)

Nice result there

I edited your post image to for one of the wider images to use IMGFS tags so it doesn't stretch the page

31-10-2009, 12:38 AM #19 (**permalink**)

Originally Posted by eva2000

Nice result there I edited your post image to for one of the wider images to use IMGFS tags so it doesn't stretch the page

Thanks. In order to get higher CPU or RAM I would have increase VCORE and /or VTT and I didn't want to kick it up more than it already is. Where are you at with your testing?

31-10-2009, 03:52 AM #20 (**permalink**)

Still early days with new i7 920 3845B260 cpu, currently testing cpu side of things = bclk testing first stop @211bclk. Gskill Trident @844Mhz 8-9-8-24 1T at 1.66v.

Super Pi 8x32M

LinX 0.6.4 - quick 5 pass test

Prime95 v25.11 64bit
Custom Blend - 5400MB

click image for full screenshots

Load and Post-load Idle

14-02-2010, 11:07 PM #21 (**permalink**)

Hello !

I have problems to config GSKILL Trident 3x2 2000Mhz at 1600 with timmings 7 7 7 20

I'm sure it is possible.

My mobo is Gigabyte X58 UD7

I test with 1,4v and 1,5v in qpi/vtt and 1,66v in vDimm but nothing helps.

Can anyone help me ?

15-02-2010, 01:12 AM #22 (**permalink**)

Try 1.36 VTT and 1.6 VDIMM 6-7-6-20 The ram should be capable but not sure of your board. I was having lots of problems due to using too much VTT. I think I am back on track....

16-02-2010, 08:41 AM #23 (**permalink**)

Originally Posted by soapman72

Try 1.36 VTT and 1.6 VDIMM 6-7-6-20 The ram should be capable but not sure of your board. I was having lots of problems due to using too much VTT. I think I am back on track....

Yes !!! I can do 6 8 7 18 !!!

16-02-2010, 10:45 AM #24 (**permalink**)

My replacement kit is on the way, as I get errors when testing using memtest, even when 1600mhz setting is used at blck of 133 and 7-7-7-20 timings. Hopefully the next kit works!