6GB Gskill Trident F3-16000CL9T-6GBTD Preliminary Test Results
This is a discussion on 6GB Gskill Trident F3-16000CL9T-6GBTD Preliminary Test Results within the DDR3 Intel Memory forums, part of the Intel memory category; Received a new triple channel memory kit from folks at Gskill - 6GB Gskill Trident F3-16000CL9T-6GBTD. The Gskill Trident F3-16000CL9T-6GBTD ...
 |
| | LinkBack | Thread Tools |
29-09-2009, 02:44 AM
| #1 (permalink) |
| Administrator |  6GB Gskill Trident F3-16000CL9T-6GBTD Preliminary Test Results
Received a new triple channel memory kit from folks at Gskill - 6GB Gskill Trident F3-16000CL9T-6GBTD. The Gskill Trident F3-16000CL9T-6GBTD is supposedly using Elpida BBSE memory ICs, while not as capable as Elpida Hyper 50mm ICs for >DDR3-2000Mhz 7-8-7-x speeds, they still hold their own for looser timings. I'll post my preliminary results here in preparation for a larger triple channel memory kit comparison review in the works          System:
First hour using this kit and managed an overclock on these for 8x 32M Pi @DDR3-2124Mhz 9-9-9-24 1T at 1.72v. Asus P6T6 WS Revolution bios sets latencies pretty tight so good pi performance even for Win7 OS Both 8x 32M Pi and single 32M Pi runs done in same windows session.   Max memory clocks @9-10-9-24 1T at 1.76v Folks are reporting higher head room mhz with 9-10-9-x timings for Elpida BBSE, and I can confirm that is correct. With 9-9-9-24 this trident kit maxing out 32M around DDR3-2124mhz with ceiling of semi-stability around 2160mhz. With 9-10-9-24 timings same trident kit pushed 32M pi @DDR3=2220mhz and managed validation @DDR3-2281Mhz all at 1.76v vdimm and 1.65v QPI/DRAM uncore volts. System:
Max Validation @DDR3-2281Mhz 9-10-9-24 1T at 1.76v   Max Screenshot @DDR3-2267Mhz 9-10-9-24 1T at 1.76v  Max Super Pi 32M @DDR3-2220Mhz 9-10-9-24 1T at 1.76v  New personal best cpuz memory validation and first time breaking DDR3-2300Mhz for triple channel on X58 @DDR3-2305Mhz 9-10-9-24 1T at 1.78v. Previous best was @DDR3-2298Mhz 9-9-9-24 with 3GB Samsung HCF0 modules. Max Validation @DDR3-2305Mhz 9-10-9-24 1T at 1.78v QPI/DRAM = 1.65625v VDIMM = 1.78v Uncore frequency = 4608Mhz   Super Pi 2M @DDR3-2256Mhz 9-10-9-24 1T at 1.78v  Shows promise, so now to let this memory kit get to know my Xeon W3540 + Asus P6T6 WS Revolution pairing |
| Last edited by eva2000; 11-12-2009 at 02:36 PM. | |
|  |
|
29-09-2009, 02:44 AM
| #2 (permalink) |
| Administrator | Timings and CMD Rate comparison Some preliminary memory tests for new 6GB Gskill Trident F3-16000CL9T-6GBTD triple channel memory kit in preparation for a larger triple channel memory kit comparison review in the works
 |
| Last edited by eva2000; 01-10-2009 at 06:06 PM. | |
|
| |
|
29-09-2009, 02:44 AM
| #3 (permalink) |
| Administrator | DDR3-2000Mhz 9-9-9-24 2T vs 1T Gskill Trident DDR3-2000Mhz kit is rated for 9-9-9-24 2T timings, so to start with testing the difference between 2T vs 1T. System:
DDR3-2000Mhz 9-9-9-24 2T CMD Rate = 2T VDIMM = 1.66v QPI/DRAM = 1.475v Super Pi 32M  Hyper Pi 8x 32M  Everest  Linx v0.6.2 All memory test 3x run Load  Complete  DDR3-2000Mhz 9-9-9-24 1T Need to bump QPI/DRAM uncore volts a tad for 1T. CMD Rate = 1T VDIMM = 1.66v QPI/DRAM = 1.48125v Super Pi 32M  Hyper Pi 8x 32M  Everest  Linx v0.6.2 All memory test 3x run Load  Complete  |
|
| |
|
29-09-2009, 02:45 AM
| #4 (permalink) |
| Administrator | DDR3-2000Mhz 8-9-8-24 2T vs 1T Now to tighten the timings @DDR3-2000Mhz 8-9-8-24 and test 2T vs 1T CMD Rate at same 1.66v vdimm and 1.48125v QPI/DRAM uncore voltage. System:
DDR3-2000Mhz 8-9-8-24 2T CMD Rate = 2T VDIMM = 1.66v QPI/DRAM = 1.48125v Super Pi 32M  Hyper Pi 8x 32M  Everest  Linx v0.6.2 All memory test 3x run Load  Complete  DDR3-2000Mhz 8-9-8-24 1T Need to bump QPI/DRAM uncore volts a tad for 1T. CMD Rate = 1T VDIMM = 1.66v QPI/DRAM = 1.48125v Super Pi 32M  Hyper Pi 8x 32M  Everest  Linx v0.6.2 All memory test 3x run Load  Complete  |
|
| |
|
29-09-2009, 02:45 AM
| #5 (permalink) |
| Administrator | DDR3-2000Mhz 7-9-7-21 tRFC = 88 2T vs 1T Further tightening of timings @DDR3-2000Mhz 7-9-7-21 with tRFC = 88 and test 2T vs 1T CMD Rate at same 1.66v vdimm and 1.4875v QPI/DRAM uncore voltage for 2T and 1.72v and 1.5v QPI/DRAM uncore voltage for 1T. System:
DDR3-2000Mhz 7-9-7-21 2T CMD Rate = 2T tRFC = 88 VDIMM = 1.66v QPI/DRAM = 1.4875v Super Pi 32M  Hyper Pi 8x 32M  Everest  Linx v0.6.2 All memory test 3x run Load  Complete  DDR3-2000Mhz 7-9-7-21 1T Need to bump QPI/DRAM uncore volts a bit but vdimm alot for 1T to pass Hyper Pi 8x 32M Pi test!. CMD Rate = 1T tRFC = 88 VDIMM = 1.72v QPI/DRAM = 1.5v Super Pi 32M  Hyper Pi 8x 32M  Everest  Linx v0.6.2 All memory test 3x run Load  Complete  |
|
| |
|
29-09-2009, 02:45 AM
| #6 (permalink) |
| Administrator | DDR3-1600Mhz 6-7-6-18 tRFC = AUTO 2T vs 1T Drop mem clocks down but tighten timings @DDR3-1600Mhz 6-7-6-18 2T vs 1T at 1.66v with much lower 1.375v QPI/DRAM uncore voltage. System:
DDR3-1600Mhz 6-7-6-18 2T CMD Rate = 2T tRFC = AUTO VDIMM = 1.66v QPI/DRAM = 1.375v Super Pi 32M  Hyper Pi 8x 32M  Everest  Linx v0.6.2 All memory test 3x run Load  Complete  DDR3-1600Mhz 6-7-6-18 1T CMD Rate = 1T tRFC = AUTO VDIMM = 1.66v QPI/DRAM = 1.375v Super Pi 32M  Hyper Pi 8x 32M  Everest  Linx v0.6.2 All memory test 3x run Load  Complete  |
| Last edited by eva2000; 30-09-2009 at 02:11 AM. | |
|
| |
|
29-09-2009, 02:46 AM
| #7 (permalink) |
| Administrator | DDR3-2100Mhz 9-9-9-24 2T vs 1T Overclocked to DDR3-2100Mhz 9-9-9-24 speeds with 2T at 1.7v vdimm and 1T needed 1.72v vdimm for LinX stability although 1T at 1.7v was enough for Hyper Pi 8x 32M Pi. System:
DDR3-2100Mhz 9-9-9-24 2T CMD Rate = 2T VDIMM = 1.7v QPI/DRAM = 1.55v Super Pi 32M  Hyper Pi 8x 32M  Everest  Linx v0.6.2 All memory test 3x run Load  Complete  DDR3-2100Mhz 9-9-9-24 1T 1T needed 1.7v for everything except for 1.72v for LinX. CMD Rate = 1T VDIMM = 1.7-1.72v QPI/DRAM = 1.55v Super Pi 32M  Hyper Pi 8x 32M  Everest  Linx v0.6.2 All memory test 3x run Load  Complete  |
| Last edited by eva2000; 01-10-2009 at 05:45 PM. | |
|
| |
|
29-09-2009, 02:46 AM
| #8 (permalink) |
| Administrator | DDR3-2100Mhz 8-9-8-24 2T vs 1T Now to tighten the timings @DDR3-2100Mhz 8-9-8-24 and test 2T vs 1T CMD Rate at same 1.72v vdimm and 1.55v QPI/DRAM uncore voltage. System:
DDR3-2100Mhz 8-9-8-24 2T CMD Rate = 2T VDIMM = 1.72v QPI/DRAM = 1.55v Super Pi 32M  Hyper Pi 8x 32M  Everest  Linx v0.6.2 All memory test 3x run Load  Complete  DDR3-2100Mhz 8-9-8-24 1T CMD Rate = 1T VDIMM = 1.72v QPI/DRAM = 1.55v Super Pi 32M  Hyper Pi 8x 32M  Everest  Linx v0.6.2 All memory test 3x run Load  Complete  |
| Last edited by eva2000; 01-10-2009 at 05:45 PM. | |
|
| |
|
| Bookmarks |
| Tags |
| asus p6t6 ws revolution, ddr3, elpida bbse, f3-16000cl9t-6gbtd, gskill trident, xeon w3540 |
« Previous Thread
|
Next Thread »
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
| Thread Tools | |
Similar Threads for: 6GB Gskill Trident F3-16000CL9T-6GBTD Preliminary Test Results
| ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Memtest86+ (v4.10) | eva2000 | General Software | 58 | 26-05-2010 07:01 AM |
| 6GB Gskill Trident F3-16000CL9T-6GBTD - AUD$209 - best value in OZ. | eva2000 | DDR3 Intel Memory | 28 | 16-12-2009 10:38 PM |
| Core i7 X58 Triple Channel DDR3 Memory kits list | eva2000 | DDR3 Intel Memory | 63 | 25-05-2009 09:26 PM |
| Core i7 and Games, Memory Testing 6GB vs 3GB | Yellowbeard | DDR3 Intel Memory | 8 | 30-01-2009 04:51 PM |
| AMD64 Overclocking Guide (07/11/06) | eva2000 | General AMD Motherboards / CPU | 7 | 02-11-2006 04:42 PM |
All times are GMT +11. The time now is 01:54 PM.
