DFI Lanparty UT X58-T3EH8 LGA1366 Photos, Bios and Overclocking Information Guide

Mafio · 24-10-2009, 06:03 AM

anyone of you have tried g.skill perfect storm 2000 cas8 elpida hyper on this mobo?

with me this ram don't run super-pi 32M or any stress test at default frequency and timings

i think that there is some kind of incompatibility with the mobo
i tried bios 428 pre-beta, 619 and 724 but nothing change

thanks

gsi16v · 28-10-2009, 10:20 AM

hello everyone !
Eva and cstkl1...you are just great !!!...this thread rocks !!
I'm new here and new in OC-ing . I run i7 920 D0 #3930A309 , dfi x58 t3e-h8, gtx295, ocz blade 2000 cl7.
My goal is :i7@4000Mhz (20x200) ddr3@2000 7-7-7-20 1T(Eva, i read your thread about dominator gt cl7 - my ocz are using same Elpida chips - so i guess oc is almost the same). But till then i get stuck with my first problem. I follow the steps that "cstkl1" wrote them here:i7 920 D0 - DFI UT X58-T3EH8 prime95/linx stability ?

here is my BIOS for the moment

Genie BIOS Setting

CPU Feature
Set VR Current Limit Max: Disabled
Thermal Management Control: Disabled
EIST Function: Disabled
CxE Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled
TDC Enable: Disabled
x TDC Limit: 0
TDP Enable: Disabled
x TDP Limit: 0

***** Logical Processor Setting *****
Intel HT Technology: disable
Active Processor Cores: All

DRAM Timing
Channel Interleave Setting: 6
Rank Interleave Setting: 4
Memory LowGap: 2304M (for gtx295 )

DRAM Command Rate: auto
CAS Latency Time (tCL):auto
RAS# to CAS# Delay (tRCD): auto
RAS# Precharge (tRP): auto
Precharge Delay (tRAS): auto
REF to ACT Delay (tRFC): AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Row Cycle Time (tRC): AUTO
Read CAS# Precharge (tRTP): AUTO
Four ACT WIN Time (tFAW): AUTO

Voltage Setting
O.C. Shut Down Free: Enable O.C.S.D.F
CPU VID Control: 1.262
CPU VID Special Add Limit: Enabled
CPU VID Special Add: Auto
Vcore Droop Control: DISABLE
DRAM Bus Voltage: 1.56V (auto by default)
DRAM PWM Switch Frequency: Nominal
DRAM PWM Phase Control: 2 Phase Operation
CPU VTT Special Add: AUTO
CPU VTT Voltage: 1.21v
VTT PWM Switch Frequency: Nominal
VTT PWM Phase Control: 2 Phase Operation
CPU PLL Voltage: 1.80v
IOH/ICH 1.1V Voltage: 1.11v
IOH Analog Voltage: 1.10v
ICH 1.5 Voltage: 1.5v
ICH 1.05V Voltage: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF: -00.0%
DIMM 3/4 DQ/DQSTB Bus VREF: -00.0%
DIMM 5/6 DQ/DQSTB Bus VREF: -00.0%
ADDR/CMD VREF Control: Disabled
x DIMM 1/2 ADDR/CMD Bus VREF: 110
x DIMM 3/4 ADDR/CMD Bus VREF: 110
x DIMM 5/6 ADDR/CMD Bus VREF: 110
CPU QPI Drive Strength: Normal
IOH QPI Drive Strength: Normal

Exit Setup Shut down: Mode 2
O.C. Fail Retry Counter: Enabled
O.C. Fail CMOS Reload: Disabled

PPM Function: Enabled
Turbo Mode Function: Disabled
1 core Max Turbo Ratio: 22x
2 core Max Turbo Ratio: 21x
3 core Max Turbo Ratio: 21x
4 core Max Turbo Ratio: 21x
CPU Non-Turbo Clock Ratio: 20x

* BCLK/UCLK/QPI Controller Settings *
QPI Control Settings: Enabled
QPI Link Fast Mode: Enabled
QPI Frequency: AUTO
CPU Base Clock (BCLK): 200 Mhz
Boot Up CPU Base Clock: 185
PCIE Clock: 100 Mhz
DRAM Frequency: auto
UnCore Frequency: auto

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

So i'm at first step...finding Vcore
runing linx 0.63 - 5.12G (max i can get) 10 rounds for 3 times with restarts ..etc...ROCK SOLID !!
But going to BIOS and Enable HT ...just HT !!.....i'm getting BSOD in 20 sec in LInx.

What am i missing ?...thanks!

cstkl1 · 13-11-2009, 03:09 PM

ok here is a table for u guys to understand

take note its only possible to find ure scaling and vtt/dram ratio and vtt/vcore ration when u have a very strong confirmed base

for mine after 4-5 boards
my bclk 200 confirmed

if u notice the downward/upward trend is to maintain the scaling
if i change and confirm one voltage i need to adjust the other two to make sure it stays on that trend

also sometimes u need more bios options to maintain this trend.
the dfi doesnt have enough.

and also it will quickly point out proc/ram/mobo/cooling limitations.
the trend tends to work best at below 80C

eva2000 · 13-11-2009, 07:05 PM

By gsi16v

hello everyone !
Eva and cstkl1...you are just great !!!...this thread rocks !!
I'm new here and new in OC-ing . I run i7 920 D0 #3930A309 , dfi x58 t3e-h8, gtx295, ocz blade 2000 cl7.
My goal is :i7@4000Mhz (20x200) ddr3@2000 7-7-7-20 1T(Eva, i read your thread about dominator gt cl7 - my ocz are using same Elpida chips - so i guess oc is almost the same). But till then i get stuck with my first problem. I follow the steps that "cstkl1" wrote them here:i7 920 D0 - DFI UT X58-T3EH8 prime95/linx stability ?

here is my BIOS for the moment

So i'm at first step...finding Vcore
runing linx 0.63 - 5.12G (max i can get) 10 rounds for 3 times with restarts ..etc...ROCK SOLID !!
But going to BIOS and Enable HT ...just HT !!.....i'm getting BSOD in 20 sec in LInx.

What am i missing ?...thanks!

Guess this post got caught in moderation queue as you you have your thread at DFI X58 UT T3E-H8 HT ON !! now

By cstkl1

ok here is a table for u guys to understand

take note its only possible to find ure scaling and vtt/dram ratio and vtt/vcore ration when u have a very strong confirmed base

for mine after 4-5 boards
my bclk 200 confirmed

if u notice the downward/upward trend is to maintain the scaling
if i change and confirm one voltage i need to adjust the other two to make sure it stays on that trend

also sometimes u need more bios options to maintain this trend.
the dfi doesnt have enough.

and also it will quickly point out proc/ram/mobo/cooling limitations.
the trend tends to work best at below 80C

Interesting, thanks for table so we can see it more clearly

Norz · 06-12-2009, 10:28 PM

Thanks eva2000 for testing and info on this DFI mobo.
I just bought it myself,will be starting testing next weekend,need some trichannel memory,then im go

Renegade5399 · 07-12-2009, 10:32 PM

You're going to love this board. I have had nothing but good luck with it since I bought it. These threads on here have been more than helpful in getting my chip to 4.4GHz with fast RAM speeds.

Now if Kingston could just send me a good set of RAM...

Dopamin3 · 10-12-2009, 02:49 PM

Well I just got this board with an i7 920, batch 3931A324.

I started overclocking and these were my PWM temps within 4 minutes, with the flame freezer installed using a good bit of OCZ Freeze. Should it be RMA'ed?

eva2000 · 10-12-2009, 10:52 PM

By Norz

Thanks eva2000 for testing and info on this DFI mobo.
I just bought it myself,will be starting testing next weekend,need some trichannel memory,then im go

hi Norz glad to hear

By Dopamin3

Well I just got this board with an i7 920, batch 3931A324.

I started overclocking and these were my PWM temps within 4 minutes, with the flame freezer installed using a good bit of OCZ Freeze. Should it be RMA'ed?

http://img267.imageshack.us/img267/9131/captureep.png

Hi Dopamin3

for pwm temps read T3eH8: very high PWM temps for discussion on pwm temps and ways to reduce the temps. It's usually normal due to individual cpu and board variances. For example my W3520 runs cpu cooler than my early i7 920 c0/d0 3851s but PWM temps were higher on W3520 on DFI UT X58-T3EH8.

Similar Threads for: DFI Lanparty UT X58-T3EH8 LGA1366 Photos, Bios and Overclocking Information Guide
Thread	Thread Starter	Forum	Replies	Last Post
DFI LANParty UT P35-T2R Preview photos & Bios Screenshots	eva2000	DFI Intel Motherboard / CPU	211	19-10-2009 02:33 AM
DFI LP UT X48-T3RS - Info, overclocking tips & photos	eva2000	DFI Intel Motherboard / CPU	11	26-09-2008 08:07 PM
DFI LANParty UT ICFX3200-T2R/G ATI RD600 Intel LGA775 Information & Photos	eva2000	DFI Intel Motherboard / CPU	57	14-12-2007 01:47 PM
AMD64 Overclocking Guide (07/11/06)	eva2000	General AMD Motherboards / CPU	7	02-11-2006 04:42 PM

Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)