rpcruz28

Hello guys
i have a really weird problem in my system and im wondering that somebody give me some reasonable explanation. I saw few persons with the same issue, but i dont have the hdd led problem. I just couldn't read any conclusion or how to solve the problem during the post ive read.
My system is:
-q6600
-Asus Blitz Formula
- 2gb OCZ Reaper pc8500
- PSU Enermax Galaxy 850w
- BFG 8800GTX
- 2 raptors raid0

The problem: dont boot correct after some changing on bios. If i just restart system is ok, but if i shut down the pc i have to switch off the psu or press the clearcmos button on the back of mobo. The system starts fine, i dont loose any setting on bios and overclock just fine!!!! THIS JUST HAPPEN WHEN I DO A SWITCH OFF FROM OS OR CHANGE FSB ON BIOS.
OK, try to contact ASUS technical assistance and after describe the weird problem said could be PSU, Case or MOBO.
The thing is, case, i doubt because ive used rubber platform to setup my system before mounting in the case, so is no electrical issue.
After many reboots and changing many times the configurations i load the default settings and the problem goes. Dont need switch off psu or press clearcmos. So i started to change settings one by one and try to see which setting on bios will start the issue. Is exactly when i change the FSB or memory frequency the problem(if i can say is a problem) starts.
I just power off my psu or reset button and everything starts normally and i could be able to use without problems at 3.5 ghz.
is just annoying!!! Restart=ok switch off= when i boot the ligths of fsb turn on 3 steps(for who knows well Blitz Formula) northbridge and sb leds stay all on. Just turn off psu or press the holly button everithing comes back to normal.
WHAT IS HAPPENING????? Should i change my mobo?
sorry for my bad English, since now best regards to all.

eva2000

welcome

what are the settings Asus Blitz Formula Bios Template and bios version used ?

NightRaven

thats weird... i have not heard of anyone with this problem in singapore.. er yea what bios?

rpcruz28

why my message didnt show? im trying to post my settings with template but ive had to write this.
Extreme Tweaker
AI Overlocking: Manual
CPU Ratio Control: Manual
--- Ratio CMOS Setting: 9
FSB Strap to North Bridge: AUTO
FSB Frequency: 333
PCIE Frequency: 100
DRAM Frequency: DDR2-1067
DRAM Command Rate: 2T
DRAM Timing Control: Manual
---CAS# Latency: 5
---RAS# to CAS# Delay: 5
---RAS# Precharge: 5
---RAS# Active Time: 15
---RAS# to RAS# Delay: AUTO
---Row Refesh Cycle Time: AUTO
---Write Recovery Time: AUTO
---Write to Read Delay: AUTO
---Read to Precharge Time: AUTO
DRAM Static Read Control: AUTO

Tramsaction Booster: AUTO

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

CPU Voltage: 1.325
CPU Voltage Reference: AUTO
Loadline Calibratiom: AUTO
FSB Termination Voltage: AUTO
North Bridge Voltage: AUTO
North Bridge Reference: AUTO
DRAM Voltage: 2.20v
-DDRII Channel A Ref Voltage: DDRII-REF
-DDRII Channel B Ref Voltage: DDRII-REF
-DDRII Controller Ref Voltage: DDRII-REF
South Bridge Voltage: AUTO
PLL Voltage: AUTO
NB LED Selection: NB Volt
SB LED Selection: PLL Volt
Frequency LED: Turn on
Voltiminder LED: Turn on

CPU Ratio Control: Manual
-- Ratio CMOS Setting: 9
C1E Support: Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Enable
CPU TM Function: Enable
Execute Disable Bit: Enable
PECI: Enable

USB Configuration
USB Functions: Enabled
Legacy USB Support: Enable(need to enable it to detect USB flash drives)

eva2000

new member posts are moderated at first if the anti-spam feature on the forum catches specific keywords or images used in new member's first couple of posts

You should be able to post properly by now

rpcruz28

tks eva2000, ive read one post here with same problem.

rpcruz28

can somebody give me a help please???

eva2000

My first guess would be Enermax psu.. got a spare psu lying around you can try ?