PC Health Status Adjust CPU Temp: Auto CPU Feature - Thermal Management Control: Disabled - PPM(EIST) Mode: Disabled - Limit CPUID MaxVal: Disabled - CIE Function: Disabled - Virtualization Technology: Disabled - Core Multi-Processing: Enabled Exist Setup Shutdown: Mode 2 Shutdown after AC Loss: Disabled O.C. Fail retry Counter 0 CPU Clock Ratio: 9x CPU N/2 Ratio: Disabled Target CPU Clock: CPU Clock: 333 Boot Up Clock: AUTO CPU Clock Amplitude: 800mv CPU Clock0 Skew: 0ps CPU Clock1 Skew: 0ps DRAM Speed: 333/1333 - Target DRAM Speed: DDR3-1333 PCIE Clock: 100mhz PCIE Slot Config: 1X 1X CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled SATA Spread Spectrum: Disabled Voltage Settings CPU VID Control: 1.10000v COY VID Special Add Limit: Enabled CPU VID Special Add: AUT0 DRAM Voltage Control: 1.57v SB Core/CPU PLL Voltage: 1.51 NB Core Voltage: 1.430 CPU VTT Voltage: 1.100 Vcore Droop Control: Enabled Clockgen Voltage Control: 3.45v GTL+ Buffers Strength: Strong Host Slew Rate: Weak x MCH RON Offset Value: x MCH RTT Offset Value: x MCH Slew Rate Offset Value: x MCH VREF 1 Value: x MCH VREF 2 Value: x MCH VREF 3 Value: GTL REF Voltage Control: Disable x CPU GTL 1/2 REF Volt: 113 x CPU GTL 0/3 REF Volt: 100 x North Bridge GTL REF Volt: 100 DRAM Timing - Enhance Data transmitting: Auto - Enhance Addressing: Auto - T2 Dispatch: Auto DRAM Default Skew Model: Model 0 to 3 Fine Delay Step Degree: 5ps to 80ps Clock Setting Fine Delay Ch1 Clock Crossing Setting: AUTO - DIMM 1 Clock fine delay: Current - DIMM 2 Clock fine delay: Current - DIMM 2 Control fine delay: Current - DIMM 1 Control fine delay: Current - Ch 1 Command fine delay: Current Ch2 Clock Crossing Setting: AUTO - DIMM 3 Clock fine delay: Current - DIMM 4 Clock fine delay: Current - DIMM 4 Control fine delay: Current - DIMM 3 Control fine delay: Current - Ch 2 Command fine delay: Current Ch1Ch2 CommonClock Setting: AUTO Ch1 RDCAS GNT-Chip Delay: Auto Ch1 WRCAS GNT-Chip Delay: Auto Ch1 Command to CS Delay: Auto Ch2 RDCAS GNT-Chip Delay: Auto Ch2 WRCAS GNT-Chip Delay: Auto Ch2 Command to CS Delay: Auto Common CMD to CS Timing: AUTO/1N/2N (command rate) CAS Latency Time (tCL): 8 RAS# to CAS# Delay (tRCD): 8 RAS# Precharge (tRP): 8 Precharge Delay (tRAS): 27 All Precharge to Act: AUTO REF to ACT Delay (tRFC): Auto Performance LVL (Read Delay) (tRD): AUTO Read delay phase adjust: Enter Ch1 Read delay phase (4~0) - Channel 1 Phase 0 Pull-In: AUTO - Channel 1 Phase 1 Pull-In: AUTO - Channel 1 Phase 2 Pull-In: AUTO - Channel 1 Phase 3 Pull-In: AUTO - Channel 1 Phase 4 Pull-In: AUTO Ch2 Read delay phase (4~0) - Channel 2 Phase 0 Pull-In: Auto - Channel 2 Phase 1 Pull-In: Auto - Channel 2 Phase 2 Pull-In: Auto - Channel 2 Phase 3 Pull-In: Auto - Channel 2 Phase 4 Pull-In: Auto MCH ODT Latency: AUTO Write to PRE Delay (tWR): AUTO Rank Write to Read (tWTR): AUTO ACT to ACT Delay (tRRD): AUTO Read to Write Delay (tRDWR): AUTO Ranks Write to Write (tWRWR): AUTO Ranks Read to Read (tRDRD): AUTO Ranks Write to Read (tWRRD): AUTO Read CAS# Precharge (tRTP): AUTO ALL PRE to Refresh: AUTO
PC Health Status Adjust CPU Temp: Auto CPU Feature - Thermal Management Control: Disabled - PPM(EIST) Mode: Disabled - Limit CPUID MaxVal: Disabled - CIE Function: Disabled - Execute Disable Bit: Disabled - Virtualization Technology: Disabled - Core Multi-Processing: Enabled Exist Setup Shutdown: Mode 2 Shutdown after AC Loss: Disabled O.C. Fail retry Counter 0 CPU Clock Ratio: 9x CPU N/2 Ratio: Disabled Target CPU Clock: CPU Clock: 333 Boot Up Clock: AUTO CPU Clock Amplitude: 800mv CPU Clock0 Skew: 0ps CPU Clock1 Skew: 0ps DRAM Speed: 333/1333 - Target DRAM Speed: DDR3-1333 PCIE Clock: 100mhz PCIE Slot Config: 1X 1X CPU Spread Spectrum: Disabled PCIE Spread Spectrum: Disabled SATA Spread Spectrum: Disabled Voltage Settings CPU VID Control: 1.10000v COY VID Special Add Limit: Enabled CPU VID Special Add: AUT0 DRAM Voltage Control: 1.57v SB Core/CPU PLL Voltage: 1.51 NB Core Voltage: 1.430 CPU VTT Voltage: 1.100 Vcore Droop Control: Enabled Clockgen Voltage Control: 3.45v GTL+ Buffers Strength: Strong Host Slew Rate: Weak GTL REF Voltage Control: Disable x CPU GTL 1/2 REF Volt: 110 x CPU GTL 0/3 REF Volt: 110 x North Bridge GTL REF Volt: 110 DRAM Timing - Enhance Data transmitting: Auto - Enhance Addressing: Auto - T2 Dispatch: Auto DLL Mode: Mode 0 Clock Setting Fine Delay Ch1 Clock Crossing Setting: AUTO - DIMM 1 Clock fine delay: Current - DIMM 2 Clock fine delay: Curren - DIMM 1 Control fine delay: Current - DIMM 2 Control fine delay: Current - Ch 1 Command fine delay: Current Ch2 Clock Crossing Setting: AUTO - DIMM 3 Clock fine delay: Current - DIMM 4 Clock fine delay: Current - DIMM 3 Control fine delay: Current - DIMM 4 Control fine delay: Current - Ch 2 Command fine delay: Current Ch1Ch2 CommonClock Setting: AUTO Ch1 RDCAS GNT-Chip Delay: Auto Ch1 WRCAS GNT-Chip Delay: Auto Ch1 Command to CS Delay: Auto Ch2 RDCAS GNT-Chip Delay: Auto Ch2 WRCAS GNT-Chip Delay: Auto Ch2 Command to CS Delay: Auto CAS Latency Time (tCL): 8 RAS# to CAS# Delay (tRCD): 8 RAS# Precharge (tRP): 8 Precharge Delay (tRAS): 27 All Precharge to Act: AUTO REF to ACT Delay (tRFC): Auto Performance LVL (Read Delay) (tRD): AUTO Read delay phase adjust: Enter Ch1 Read delay phase (4~0) - Channel 1 Phase 0 Pull-In: AUTO - Channel 1 Phase 1 Pull-In: AUTO - Channel 1 Phase 2 Pull-In: AUTO - Channel 1 Phase 3 Pull-In: AUTO - Channel 1 Phase 4 Pull-In: AUTO Ch2 Read delay phase (4~0) - Channel 2 Phase 0 Pull-In: Auto - Channel 2 Phase 1 Pull-In: Auto - Channel 2 Phase 2 Pull-In: Auto - Channel 2 Phase 3 Pull-In: Auto - Channel 2 Phase 4 Pull-In: Auto MCH ODT Latency: AUTO Write to PRE Delay (tWR): AUTO Rank Write to Read (tWTR): AUTO ACT to ACT Delay (tRRD): AUTO Read to Write Delay (tRDWR): AUTO Ranks Write to Write (tWRWR): AUTO Ranks Read to Read (tRDRD): AUTO Ranks Write to Read (tWRRD): AUTO Read CAS# Precharge (tRTP): AUTO ALL PRE to Refresh: AUTO CMD to CST mode: AUTO/1T/2T
07-06-2008, 08:53 AM
#2 (permalink)